ORIGINAL_ARTICLE
بررسی و مقایسه دو مکانیسم انتقالی و دورانی در تحلیل سهبعدی پایداری لرزهای شیروانیها به روش تحلیل حدی مرز بالا
در این مقاله بر مبنای روش تحلیل حدی مرز بالا به بررسی پایداری سهبعدی شیروانیها در مقابل زلزله بر اساس مکانیسمهای گسیختگی دورانی و انتقالی و نیز مقایسه نتایج آنها پرداخته شده است. تعریف سطوح جانبی مکانیسمهای گسیختگی سهبعدی در روش مرز بالا مستلزم رعایت قانون جریان وابسته است که تشکیل صفحات جانبی مسطح را در مکانیسم انتقالی بسیار مقید میکند و در حالت مکانیسم دورانی لازم است معادلات این سطوح، معادله دیفرانسیل خاصی را ارضا کنند. در ادامه تحقیقات مربوط به پایداری سهبعدی شیروانیهای خاکی به روش مرز بالا با استفاده از مکانیسمهای انتقالی و دورانی، تحقیق حاضر به مقایسه نتایج حاصل از یک مکانیسم انتقالی با یک مکانیسم دورانی که الگوریتم آن در این تحقیق بر اساس حل نهایی میخالوفسکی و به روشی سادهتر تدوین شده است، میپردازد. بهطورکلی روند تغییرات ضریب پایداری شیروانی با افزایش ضریب زلزله برای هر دو مکانیسم دورانی و انتقالی تقریباً مشابه است. همچنین اهمیت تحلیلهای سهبعدی در حالت لرزهای نسبت به حالت استاتیکی بیشتر است. نتایج حاصل از این تحقیق نشان میدهد که مکانیسم دورانی در اکثر موارد و بهخصوص در شیبهای قائم نتایج بهتری ارائه میدهد، اگرچه مکانیسم انتقالی برای خاکهای چسبنده و با مکانیسمهای مقید نتایج بهتری دارد.
http://www.bese.ir/article_240404_02bf7a29ee010258c64f712b0f855d18.pdf
2019-12-22
1
10
پایداری شیروانیها
مکانیسم دورانی
مکانیسم انتقالی
تحلیل حدی مرز بالا
تحلیل سهبعدی
بهزاد
امیرلو
1
پردیس دانشکدههای فنی، دانشگاه تهران، تهران، ایران
AUTHOR
اورنگ
فرزانه
ofarzane@ut.ac.ir
2
دانشکده عمران، پردیس دانشکدههای فنی، دانشگاه تهران، تهران، ایران
AUTHOR
فرج اله
عسکری
askari@iiees.ac.ir
3
پژوهشکده مهندسی ژئوتکنیک، پژوهشگاه بین المللی زلزلهشناسی و مهندسی زلزله، تهران، ایران،
LEAD_AUTHOR
- Amirloo, B. (2017) Analysis of Three-Dimensional Soil Slopes Stability Based on Upper Bound Limit Analysis Using Rotational Failure Mechanisms. Masterâs Thesis, University of Tehran, Iran (In Persian).
1
- Askari, F. (1999) Three-Dimensional Analysis of Homogeneous and Nonhomogeneous Slopes in Static and Dynamic Mode Using Upper Bound Theorem of Limit Analysis. Ph.D. Dissertation Thesis, University of Tehran, Iran (in Persian).
2
- Giger, M.W. & Krizek, R.J. (1975) Stability analysis of vertical cut with variable corner angle. Soils and Foundation, 15(2), 63-71.
3
- DeBuhan, P. and Garnier, D. (1998) Three dimensional bearing capacity analysis of a foundation near a slope. Soil and Foundations, 38(3), 153-163.
4
- Fazelinia, M. (2006) Analysis of Three-Dimensional Slopes Stability Based on Rotational Failure Mechanisms. Masterâs Thesis, University of Tehran, Iran (in Persian).
5
- Michalowski, R.L. and Drescher, A. (2009) Three-dimensional stability of slopes and excavations. Geotechnique, 59(10), 839-850.
6
- Michalowski, R.L. (1989) Three-dimensional analysis of locally loaded slopes. Geotechnique, London, 39(1), 27-38.
7
- Farzaneh, O. and Askari, F. (2003) Three-dimensional analysis of nonhomogeneous slopes. ASCE, Journal of Geotechnical and Geoenviromental Engineering, 129(2), 137-145.
8
- Chen, W.F. and Liu (1990) Limit Analysis in Soil Mechanics, Elsevier Science Publishers, B.V.
9
- Askari, F. and Farzaneh, O. (2003) Upper-bound solution for seismic bearing capacity of shallow foundations near slopes. Geotechnique, 53(8), 697-702.
10
- Ganjian, N. (2002) Analysis of Three-Dimensional Stability of Arch Slopes in Plan Based on Upper Bound Limit Analysis. Masterâs Thesis, University of Tehran, Iran (in Persian).
11
ORIGINAL_ARTICLE
تعیین عملکرد رفتار دینامیکی دیوارهای خاکی میخ گذاری شده تحت بارگذاریهای لرزهای بر اساس تغییر مکان
با توجه به گسترش روزافزون بهرهوری از فضاهای زیرسطحی، نیاز بشر به پایدارسازی در زمان حفر و گودبرداری بیش از پیش قوت میگیرد. پایدارسازی و بررسی این روش در حالت دینامیکی به دلیل بهرهمندی در سازههای دائمی نظیر پایداری شیب کناره راه از اهمیت بالایی برخوردار است. یکی از روشهای پایدارسازی دیوارههای گود استفاده از روش میخگذاری است. لذا در این مقاله رفتار پایدارسازی دیوارهای میخگذاری شده دائمی تحت بار دینامیکی مورد بحث و بررسی قرار گرفته است. به کمک ابزارگذاریهای صورت گرفته در گود هتل نرگس شماره 2 و مدلسازی آن با استفاده از نرمافزار FLAC صحت این نرمافزار مورد تأیید قرار گرفت. سپس با در نظر گرفتن 15 نگاشت و ساختگاههای نوع 1، 2 و 3 بر اساس آییننامه 2800، بارهای هارمونیک معادل محاسبه شده و تحلیلهای دینامیکی برای چهار بار هارمونیک معادل، سه ساختگاه و سه ارتفاع مختلف 3، 6 و 9 متر و در دو زاویه مختلف میخگذاری انجام شد. برای این منظور با در نظر گرفتن تغییر شکل لبه بالایی دیواره بهعنوان معیار مقایسه بین تحلیلها، مقادیر تغییر مکان در 72 حالت مختلف مشخص شد. بررسی نتایج تحلیلهای فوق نشان داد که، با کاهش مشخصههای مقاومتی ساختگاه (از نوع 1 به 3) جابهجایی افقی لبه گود و پوسته نما افزایش یافته و با کاهش زاویه میخها جابهجایی افقی لبه گود و پوسته نما کاهش مییابد.
http://www.bese.ir/article_240406_695dd79c01e4024d3d57356d96844530.pdf
2019-12-22
11
21
خاک مسلح
رفتار دینامیکی
دیوار میخگذاری شده
تحلیل تفاضل محدود
ایرج
رحمانی
i.rahmani@bhrc.ac.ir
1
بخش ژئوتکنیک و زیرساخت، مرکز تحقیقات راه، مسکن و شهرسازی، تهران، ایران
LEAD_AUTHOR
امیر
نجاتی
a.nejati@ce142.com
2
دانشکده فنی و مهندسی، دانشگاه آزاد اسلامی، واحد تهران مرکز، تهران، ایران
AUTHOR
Lazarte, C.A., Elias, V., Espinoza, R.D., Sabatini, P.J. (2003) Geotechnical Engineering Circular No. 7, Soil Nail Walls. Federal Highway Administration (FHWA), Report No. FHWA0-IF-03-017. Washington, DC., USA.
1
Mononobe, N. and Matsuo, H. (1929) On the Determination of Earth Pressure during Earthquakes, Proceedings, World Eng. Conference, 9, 176.
2
Okabe, S. (1926) General Theory of Earth Pressure. Journal of the Japanese Society of Civil Engineers, Tokyo, Japan, 12(1).
3
Pedley, M.J. (1992) Ground modification on soil and rock anchorage, rock bolting, soil nailing and dowelling. Soil Nailing Lecture Notes on Ground Modification Seminar, University of Technology, Sydney, 51â89.
4
Davis, M.C.R., Jacob, C.D., and Bridle, R.J. (1993) An Experimental Investigation of Soil Nailing Retaining Structures. Thomas Telford, London.
5
Turner, J.P. and Jensen, W.G. (2005) Landslide stabilization using soil nail and mechanically stabilized earth walls: case study. Journal of Geotechnical and Geoenvironmental Engineering, 131(2), 141â150.
6
Li, J., Tham, L.G., Junaideen, S.M., Yue, Z.Q., and Lee, C.F. (2008) Loose fill slope stabilization with soil nails: full-scale test. Journal of Geotechnical and Geoenvironmental Engineering, ASCE, 134(3), 277-288.
7
Ehrlich, M., and Silva, R.C. (2015) Behavior of a 31 m high excavation supported by anchoring and nailing in residual soil of gneiss. Engineering Geology, 191, 48-60.
8
Gutierrez, V., and Tatsuoka, A.F. (1988) Role of facing in reinforcing cohesion less soil slopes by means of metal strips. Proceedings of the International Geotechnical Symposium on Theory and Practice of Earth Reinforcement, Kyushu, Japan, 289â294.
9
Vucetic, M., Tufenkjian, M., Doroudian, M. (1993) Dynamic Centrifuge Testing of Soil-Nailed Excavations. Geotechnical Testing Journal, 16(2), 172â187.
10
Mark, R.T. and Mladen, V. (2000) Dynamic failure mechanism of soil-nailed excavation models in centrifuge. Journal of Geotechnical and Geoenvironmental Engineering, 126(3), 227-235.
11
Zhang, J.P., Zhang, J., Qui, T. (2001) Model test by centrifuge of soil nail reinforcements. Journal of Testing and Evaluation, 29(4), 315-328.
12
Zhang, G., Cao, J., Wang, L. (2013) Centrifuge model tests of deformation and failure of nailing reinforced slope under vertical surface loading conditions. Soils and Foundations, 53(1), 117-129.
13
Rotte, V.M., and Viswanadham, B.V.S. (2013) Centrifuge Model Studies on the Performance of Slopes with and without Nails Subjected to Seepage. Proceedings of Indian Geotechnical Conference, Roorkee, 1-8.
14
Zhang, G., Cao, J., Wang, L. (2014) Failure behavior and mechanism of slopes reinforced using soil nail wall under various loading conditions. Soils and Foundations, 54(6), 1175-1187.
15
Sivakumar Babu, G.L., and Murthy B.R.S. (2002) Analysis of construction factors influencing the behavior of soil nailed earth retaining walls. Ground Improvement, 6(3), 137â143.
16
Cheuk, C.Y., Ng, C.W.W., and Sun, H.W. (2005) Numerical experiments of soil nails in loose fill slopes subjected to rainfall infiltration effects. Computers and Geotechnics, 32(4), 290â303.
17
Sheikhbahaei, A.M., Halabian, A.M., and Hashemolhosseini, S.H. (2010) Analysis of soil nailed walls under harmonic dynamic excitations using finite difference method. Fifth International Conference on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, San Diego, California.
18
Wu, J.C., and Shi, R. (2012) Seismic Analysis of Soil Nailed Wall Using Finite Element Method. Advanced Materials Research, 535-537, 2027-2031.
19
Jaya, V., and Annie, J. (2013) An Investigation on the Dynamic Behavior of Soil Nail Walls. Journal of Civil Engineering and Science, 2(4), 241-249.
20
Itasca (1995) FLAC: Fast Lagrangian Analysis of Continua, Version 3.3, User Manual, Itasca Consulting Group, Inc., Minneapolis.
21
Soheil, G., and Saidi, M. (2011) An Investigation on the Behavior of Retaining Structure of Excavation Wall Using Obtained Result from Numerical Modeling and Monitoring Approach (A Case Study of International "Narges Razavi 2 Hotel", Mashhad), Journal of Structural Engineering and Geotechnics.
22
Komakpanah, A., and Yazdandoust, M., (2015) Investigation into the effect of earthquake index parameters on seismic performance of reinforced soil walls to select an appropriate design earthquake, 3.12(1.1), 17-26.
23
Hashash, Y.M.A., Musgrove, M.I., Harmon, J.A., Groholski, D.R., Phillips, C.A., and Park, D. (2016) DEEPSOIL 6.1, User Manual.
24
ORIGINAL_ARTICLE
ارزیابی مشخصات دینامیکی ساختمانها در مقایسه تحلیل عددی و روش تجربی نسبت طیفی H/V میکروترمورها
فرکانس طبیعی پارامتری است که نقش کلیدی در طراحی دینامیکی سازهها و ارزیابی آسیبپذیری ساختمانها دارد. در استانداردهای زلزله برای تخمین فرکانس طبیعی از روشهای تحلیلی و روابط تجربی استفاده شده است، ولی با توجه به تأثیر عوامل مختلف مانند شیوه طراحی، مصالح ساختمان، شرایط ساختگاه، این روابط هنوز از اعتماد کافی برخوردار نیستند. برای تخمین فرکانس طبیعی ساختمان میتوان از تحلیل عددی سازه و یا روابط تجربی حاصل از تحلیل نسبت طیفی میکروترمورها استفاده کرد. تحقیق حاضر به بررسی عوامل مؤثر بر تغییر فرکانس طبیعی سازه مانند عمر سازه و مسائل اجرایی پرداخته است. بدینمنظور از دو روش تجربی و عددی استفاده شد. در ابتدا مقادیر فرکانس طبیعی حاصل از محاسبه نسبت طیفی H/V میکروترمور مربوط به 12 ساختمان شامل 6 ساختمان نوساز و 6 ساختمان قدیمی در شهر شیراز تخمین زده شد و از دو روش تحلیلی و تجربی روابط همبستگی میان فرکانس تشدید با طبقات تخمین زده شد. نتایج نشان میدهد که از دادههای میکروترمور میتوان برای تحلیل پاسخ لرزهای ساختمانها استفاده کرد. بهعلاوه نتایج محاسبات سازه به روش تحلیل عددی در مقایسه با تحلیلهای نسبت طیفی H/V به دلیل اعمال ضرایب ایمنی در استانداردها محافظهکارانه است. همچنین تغییرات فرکانس ساختمان با افزایش طبقات بهصورت توابع توانی و یا دو جملهای کاهشی است. عمر سازه و تغییر ضوابط آییننامهای تغییرات حدود 40 الی 50 درصدی را در مقدار فرکانس ایجاد میکند.
http://www.bese.ir/article_240411_9d15eb708b10ada8e339d6e3cdba2e92.pdf
2019-12-22
23
36
فرکانس
میکروترمور
ارتعاش محیطی
میرایی
اثر ساختگاه
مهدی
مخبری
m_mokhberi@iauest.ac.ir
1
گروه مهندسی عمران، دانشگاه آزاد اسلامی، واحد استهبان، استهبان، ایران
LEAD_AUTHOR
- Gosar, A. (2010) Site effects and soil-structure resonance study in the Kobarid basin (NW Slovenia) using microtremors. Natural Hazards and Earth System Sciences, 10(4), 761.
1
- Herak, M. (2011) Overview of recent ambient noise measurements in Croatia in free-field and in buildings. Geofizika, 28(1), 21-40.
2
- Mucciarelli, M., Herak, M. and Cassidy, J. (2008) Increasing Seismic Safety by Combining Engineering Technologies and Seismological Data. Springer Science & Business Media.
3
- Cole Jr, H.A. (1973) On-Line Failure Detection and Damping Measurement of Aerospace Structures by Random Decrement Signatures.
4
- Farsi, M., et al. (2010) Evaluation of the quality of repairing and strengthening of buildings. Proceedings of the 14th ECEE.
5
- Nakamura, Y., Gurler, E.D. Saita, J., Rovelli, A., Donati, S. (2000) Vulnerability investigation of Roman Colosseum using microtremor. Proceeding, 12th WCEE, p. 1-8.
6
- Sato, T., Nakamura, Y. and Saita, J. (2008) The change of the dynamic characteristics using microtremor. The 14th World Conference on Earthquake Engineering.
7
- Kareem, A. and Gurley, K. (1996) Damping in structures: its evaluation and treatment of uncertainty. Journal of Wind Engineering and Industrial Aerodynamics, 59(2), 131-157.
8
- Arakawa, T. and Yamamoto, K. (2004) Frequencies and damping ratios of a high rise building based on microtremor measurement. Proc., 13th World Conference on Earthquake Engineering.
9
- Crowley, H. and Pinho, R. (2010) Revisiting Eurocode 8 formulae for periods of vibration and their employment in linear seismic analysis. Earthquake Engineering & Structural Dynamics, 39(2), 223-235.
10
- Hans, S., Boutin, C., Ibraim, E., Roussillon, P. (2005) In situ experiments and seismic analysis of existing buildings. Part I: Experimental investigations. Earthquake Engineering & Structural Dynamics, 34(12), 1513-1529.
11
- Calvi, G.M., Pinho, R. and Crowley, H. (2006) State-of-the-knowledge on the period elongation of RC buildings during strong ground shaking. Proc. of the 1st European Conference of Earthquake Engineering and Seismology, Geneva, Switzerland.
12
- Farsi, M.N. and Bard, P.-Y. (2004) Estimation des periodes propres de bâtiments et vulnerabilite du bâti existant dans l'agglomeration de Grenoble. Revue Française de Genie Civil, 8(2-3), 149-179.
13
- Brincker, R., Zhang, L. and Andersen, P. (2001) Modal identification of output-only systems using frequency domain decomposition. Smart Materials and Structures, 10(3), 441.
14
- Dunand, F., Bard, P.-Y. and Rodgers, J. (2006) Coimparison of the Dynamic Parameters Extracted from Weak, Moderate and Strong Motion Recorded in Buildings.
15
- Housner, G. and Brady, A. (1963) 'Natural Periods of Buildings'. In Selected Earthquake Engineering Papers of George W. Housner. ASCE.
16
- Carder, D.S. (1937) Observed vibrations of bridges. Bulletin of the Seismological Society of America, 27(4), 267-303.
17
- Hong, L.L. and Hwang, W.L. (2000) Empirical formula for fundamental vibration periods of reinforced concrete buildings in Taiwan. Earthquake Engineering & Structural Dynamics, 29(3), 327-337.
18
- CEN, E. (2004) Design of Structures for Earthquake ResistanceâPart 1: General Rules, Seismic Actions and Rules for Buildings. European Committee for Standardization, p. 1998-1:2004.
19
- SIA, S.S. (2003) 'Actions on Structures'. In SIA 261:2003 Civil Engineering, SN 505 26.1 Swiss Society of Engineers and Architects.
20
- Lagomarsino, S. and Giovinazzi, S. (2006) Macroseismic and mechanical models for the vulnerability and damage assessment of current buildings. Bulletin of Earthquake Engineering, 4(4), 415-443.
21
- Goel, R.K. and Chopra, A.K. (1998) Period formulas for concrete shear wall buildings. Journal of Structural Engineering, 124(4), 426-433.
22
- Michel, C., Gueguen, P., Lestuzzi, P. & Bard, P.-Y. (2010) Comparison between seismic vulnerability models and experimental dynamic properties of existing buildings in France. Bulletin of Earthquake Engineering, 8(6), 1295-1307.
23
- Nakamura, Y. (1989) A method for dynamic characteristics estimation of subsurface using microtremor on the ground surface. Railway Technical Research Institute, Quarterly Reports, 30(1).
24
- Nakamura, Y. (1996) Real-time information systems for hazards mitigation. Proceedings of the 11th World Conference on Earthquake Engineering, Acapulco, Mexico.
25
- Mokhberi, M. (2015) Vulnerability evaluation of the urban area using the H/V spectral ratio of microtremors. International Journal of Disaster Risk Reduction, 13, 369-374.
26
ORIGINAL_ARTICLE
ارزیابی روابط ریاضی سرعت موج برشی و نتایج آزمون نفوذ استاندارد با رویکرد آمار بیزین
سرعت موج برشی بهعنوان یکی از مهمترین پارامترهای ژئوفیزیکی میباشد که پاسخ لرزهای سایتها در قالب آن بیان میشود. این پارامتر لرزهای اطلاعات ارزشمندی راجع به ساختگاه پروژه را میدهد اما ازآنجاییکه آزمایشهای ژئوفیزیکی معمولاً گران و زمانبر هستند استفاده از روشهای غیر مستقیم بهمنظور کاهش هزینهها رو به افزایش است. تحقیقات زیادی دراینباره در مناطق مختلف جهان انجام شده است که در اکثریت آنها از دو معادله توانی ساده و توانی چندگانه جهت استخراج معادلات استفاده کردهاند. اما این تحقیق با استفاده از توابع جدید تعریف شده توسط آمار بیزین نشان داده است که معادلاتی با اعتباری بهمراتب بیشتر از روابط موجود در سوابق تحقیق میتوانند جهت تخمین سرعت موج برشی بهکار گرفته شوند.
http://www.bese.ir/article_240412_92c7d8f474f7594b772349f04e78ab71.pdf
2019-12-22
37
51
سرعت موج برشی
آزمون نفوذ استاندارد
همبستگی آماری
آمار بیزین
سولماز
چاروسایی
1
گروه مهندسی عمران، واحد اهواز، دانشگاه آزاد اسلامی، اهواز، ایران
AUTHOR
نوید
خیاط
khayat@iauahvaz.ac.ir
2
گروه مهندسی عمران، واحد اهواز، دانشگاه آزاد اسلامی، اهواز، ایران
LEAD_AUTHOR
مهدی
مهدوی عادلی
3
گروه مهندسی عمران، واحد شوشتر، دانشگاه آزاد اسلامی، شوشتر، ایران
AUTHOR
Hanumantharao, C. and Ramana, G. (2008) Dynamic soil properties for microzonation of Delhi, India. Journal of earth system science, 117(2), 719-730.
1
Choi, Y. and Stewart, J.P. (2005) Nonlinear site amplification as function of 30 m shear wave velocity. Earthquake Spectra, 21(1), 1-30.
2
Andrus, R.D., Fairbanks, C.D., Zhang, J., Camp, W.M., Casey, T.J., Cleary, T.J., Wright, W.B. (2006) Shear-wave velocity and seismic response of near-surface sediments in Charleston, South Carolina. Bulletin of the Seismological Society of America, 96(5), 1897-1914.
3
Esfehanizadeh, M., Nabizadeh, F. and Yazarloo, R. (2015) Correlation between standard penetration (NSPT) and shear wave velocity (VS) for young coastal sands of the Caspian Sea. Arabian Journal of Geosciences, 8(9), 7333-7341.
4
Rollins, K.M., Diehl, N.B. and Weaver, T.J. (1998) Implications of V s-BPT (N 1) 6 0 Correlations for Liquefaction Assessment in Gravels. Geotechnical Earthquake Engineering and Soil Dynamics III, ASCE.
5
Thaker, T. and Rao, K. (2011) Development of statistical correlations between shear wave velocity and penetration resistance using MASW technique. Geo-Innovation Addressing Global Challenges, Toronto, Ontario, Canada,.
6
Nazarian, S. (1984) In situ shear wave velocities from spectral analysis of surface wave. Proceedings of 8th Conference on Earthquake Engineering, San Francisco.
7
Jafari, M.K., Shafiee, A. and Razmkhah, A. (2002) Dynamic properties of fine grained soils in south of Tehran. Journal of Seismology and Earthquake Engineering, 4(1), 25-35.
8
Hasancebi, N. and Ulusay, R. (2007) Empirical correlations between shear wave velocity and penetration resistance for ground shaking assessments. Bulletin of Engineering Geology and the Environment, 66(2), 203-213.
9
Fauzi, A., Irsyam, M. and Fauzi, U.J. (2014) Empirical correlation of shear wave velocity and N-SPT value for Jakarta. Int. J. GEOMATE, 7(1), 980-984.
10
Brown, L.T., Boore, D.M. and Stokoe, K.H. (2002) Comparison of shear-wave slowness profiles at 10 strong-motion sites from noninvasive SASW measurements and measurements made in boreholes. Bulletin of the Seismological Society of America, 92(8), 3116-3133.
11
Andrus, R., Zhang, J., Ellis, B.S., Juang, C.H. (2003) Guide for Estimating the Dynamic Properties of South Carolina Soils for Ground Response Analysis.
12
Silva, W., Wong, I., Siegel, T., Gregor, N., Darragh, R., Lee, R. (2003) Ground motion and liquefaction simulation of the 1886 Charleston, South Carolina, earthquake. Bulletin of the Seismological Society of America, 93(6), 2717-2736.
13
Mohanan, N.P., et al. (2006) Electronic Files of Shear Wave Velocity and Cone Penetration Test Measurements from the Greater Charleston Area, South Carolina. Data Rep. to the US Geological Survey, Award No. 05HQGR0037.
14
Seed, H. and Idriss, I. (1981) Evaluation of liquefaction potential sand deposits based on observation of performance in previous earthquakes. ASCE National Convention (MO).
15
Lee, S.H.H. (1990) Regression models of shear wave velocities in Taipei basin. Journal of the Chinese Institute of Engineers, 13(5), 519-532.
16
Jafari, M., Asghari, A., and Rahmani, I. (1997) Empirical correlation between shear wave velocity (Vs) and SPT-N value for south of Tehran soils. Proc. 4th International Conference on Civil Engineering.
17
Ohta, Y. and Goto, N. (1978) Empirical shear wave velocity equations in terms of characteristic soil indexes. Earthquake Engineering & Structural Dynamics, 6(2), 167-187.
18
Brandenberg, S.J., Bellana, N. and Shantz, T. (2010) Shear wave velocity as function of standard penetration test resistance and vertical effective stress at California bridge sites. Soil Dynamics and Earthquake Engineering, 30(10), 1026-1035.
19
Ghorbani, A., Jafarian, Y. and Maghsoudi, M.S. (2012) Estimating shear wave velocity of soil deposits using polynomial neural networks: Application to liquefaction. Computers & Geosciences, 44, 86-94.
20
Standard, A. (2008) Standard test method for standard penetration test (SPT) and split-barrel sampling of soils.
21
Lee, S. (1988) Regression model for shear wave velocity of sandy and silty soils of Taipei basin. Proc. of the CCNAA-AIT Joint Seminar/Workshop on Research and Application for Multiple Hazards Mitigation, Taipei.
22
Der Kiureghian, A. (1999) A Bayesian framework for fragility assessment. Proc., ICASP8 Conference.
23
Brezger, A. and Lang, S. (2006) Generalized structured additive regression based on Bayesian P-splines. Computational Statistics & Data Analysis, 50(4), 967-991.
24
Brezger, A. and Lang, S. (2008) Simultaneous probability statements for Bayesian P-splines. Statistical Modelling, 8(2), 141-168.
25
ORIGINAL_ARTICLE
تعمیم نسل جدید روابط کاهندگی برای پیش بینی بیشینه شتاب زمین با استفاده از روش تحلیل بازنمونه گیری از داده ها
پیشبینی واقعگرایانه بیشینه شتاب زمین (PGA)، بهمنظور استفاده در طراحی سازه های مقاوم در برابر زلزله، بهخصوص در مناطق لرزه خیز از اهمیت ویژه ای برخوردار است. با استفاده از تحلیل خطر احتمالاتی زلزله، میزان لرزه خیزی یک منطقه هنگام وقوع زلزله مشخص میگردد. بنابراین یکی از مهمترین بخشهای تحلیل خطر، پیشبینی جنبشهای نیرومند زمین میباشد که توسط روابطی موسوم به روابط کاهندگی به دست می آیند. مرکز مطالعات مهندسی زلزله (Peer) روابطی را تحت عناوین روابط کاهندگی NGA-West1 و NGA-West2 برای کل جهان ارائه نموده است. ازآنجاکه یک رابطه کاهندگی باید بتواند در برابر آزمونهای آماری نظیر آزمون تحلیل بازنمونه گیری از داده ها که اخیراً توسط آذربخت و همکاران [1] ارائه گردیده است، نتایج مطلوبی را در بر داشته باشد، بنابراین در این پژوهش سعی می شود ضرایب برخی روابط کاهندگی نسل جدید نظیر کمپبل و بزرگنیا [2]، آبراهامسون و سیلوا [3] و رابطه بور و اتکینسون [4] بر اساس مجموعه داده های منتشر شده توسط مرکز مطالعات مهندسی زلزله و با بهره گیری از الگوریتم ژنتیک چند هدفه، برای بیشینه شتاب زمین، بهینهسازی شوند. نتایج بیانگر تطبیق خوب روابط بهدستآمده در برابر سایر آزمون های آماری میباشد. انتظار میرود بتوان از نتایج حاصل از این پژوهش در تحلیل خطر احتمالاتی زلزله بهره گرفت.
http://www.bese.ir/article_240413_ffcd1b3b3953dff665db8135238d39f7.pdf
2019-12-22
53
74
تحلیل خطر لرزهای
روابط کاهندگی نسل جدید
الگوریتم ژنتیک چند هدفه
تحلیل حساسیت
کاتالوگ لرزهای
علیرضا
آذربخت
azarbakht@gmail.com
1
گروه مهندسی عمران، دانشکده فنی مهندسی، دانشگاه اراک، اراک، ایران
LEAD_AUTHOR
حامد
زینلی
2
دانشکده فنی مهندسی، دانشگاه اراک، اراک، ایران
AUTHOR
زینت
رجبی
3
دانشکده فنی مهندسی، دانشگاه اراک، اراک، ایران
AUTHOR
- Azarbakht, A., Rahpeyma, S., Mousavi, M. (2014) A new methodology for assessment the stability of Ground Motion Prediction Equations. Bulletin of the Seismological Society of America, 104(3), doi:10.1785/0120130212.
1
- Campbell, K.W. (2014) NGA-West2 Campbell-Bozorgnia ground motion model for the horizontal components of PGA, PGV, and 5%-damped elastic pseudo-acceleration response spectra for periods ranging from 0.01 to 10 sec. Earthquake Spectra.
2
- Abrahamson, N.A., Silva, W.J. (2008) Summary of the Abrahamson & Silva NGA ground motion relations. Earthquake Spectra, 24, 67-97.
3
- Boore, D.M., Atkinson, G.M. (2008) Ground-Motion Prediction Equations for the Average Horizontal Component of PGA, PGV, and 5%-Damped PSA at Spectral Periods between 0.01 s and 10.0 s. Earthquake Spectra, 24(1), 99-138.
4
- Toro, G. (2006) The effects of ground-motion uncertainity on seismic hazard results: Examples and approximate results. Annual Meeting of the Seismo Seismological Society of America, San Francisco.
5
- Rahpeyma, S.A., Azarbakht, A. (2015) Compatibility Assessment Of Ground Motion Attenuation Models With The Iran Plateau Database. Civil Engineering Sharif, 31.2(1.1), 137-146.
6
- PEER, Pacific Earthquake Engineering Research Center, NGA Database, University of California, Berkeley. Available from: http://peer.berkeley.edu/ngawest/nga.
7
- Scherbaum, F., Delavaud, E. and Riggelsen, C. (2009) Model selection in seismic hazard analysis: an information-theoretic perspective. Bulletin of the Seismological Society of America, 99, 3234-3247.
8
- زÙÙÙÙ ØاÙ
د (1395) تÙسع٠Ùس٠ØدÙد رÙابط کاÙÙدگ٠برا٠پÙØ´ÂبÙÙ٠بÙØ´ÙÙ٠شتاب زÙ
Ù٠با استÙاد٠از رÙØ´ تØÙÙ٠بازÙÙ
ÙÙÙÂÚ¯Ùر٠از دادÙÂÙا. پاÙاÙâÙاÙ
Ù Ø§Ø±Ø´Ø¯Ø Ø¯Ø§Ùشگا٠ÙÙÙ Ù
ÙÙØ¯Ø³Ù Ø§Ø±Ø§Ú©Ø Ø²Ù
ستاÙ.
9
- Campbell, K.W., Bozorgnia, Y. (2008) NGA Ground Motion Model for the Geometric Mean Horizontal Component of PGA, PGV, PGD and 5% Damped Linear Elastic Response Spectra for Periods Ranging from 0.01 to 10 s. Earthquake Spectra, 24(1), 139-171.
10
- Chiou, B.S.J., Youngs, R.R. (2008) An NGA Model for the Average Horizontal Component of Peak Ground Motion and Response Spectra. Earthquake Spectra, 24(1), 173-215.
11
- Boore, D.M., Stewart, J.P., Seyhan, E., Atkinson G.M. (2013) NGA-West2 Equations for Predicting Response Spectral Accelerations for Shallow Crustal Earthquakes. PEER Report 5.
12
- Chiou, B.S.J., Youngs, R.R. (2014) Update of the Chiou and Youngs NGA model for the average horizontal component of peak ground motion and response spectra. Earthquake Spectra, 30(3), 1117-1153.
13
- Abrahamson, N.A., Silva, W.J., Kamai, R. (2013) Update of the AS08 Ground-Motion Prediction Equations Based on the NGA-West2 Data Set. Pacific Engineering Research Center Report 4.
14
- Abrahamson, N.A., Youngs, R.R. (1992) Short Notes: A stable algorithm for regression analyses using the random effects model. Bulletin of the Seismological Society of America, 82, 505-510.
15
- Turchin, P., Grinin, L., Korotayev, A., Munck, V.C. de (2007) History and mathematics: Historical Dynamics and Development of Complex Societies.
16
- Delavaud, E., Scherbaum, F., Kuehn, N., Riggelsen, C. (2009) Information-Theoretic Selection of Ground-Motion Prediction Equations for Seismic Hazard Analysis: An Applicability Study Using Californian Data. Bulletin of the Seismological Society of America, 99, 3248-3263.
17
- Scherbaum, F., Cotton, F. and Smit, P. (2004) On the use of response spectralreference data for the selection of ground-motion models for seismic hazard analysis: The case of rock motion. Bulletin of the Seismological Society of America, 94(6), 341-348.
18
- Bazzurro, P. and Cornell, C.A. (1999) Disaggregation of seismic hazard. Bulletin of the Seismological Society of America, 501-520.
19
- Baker, J.W. (2008) An Introduction to Probabilistic Seismic Hazard Analysis (PSHA). version 1.3, Available online : http://www.stanford.edu/~bakerjw., p. 72.
20
ORIGINAL_ARTICLE
بهبود رفتار سیستم دیوار برشی فولادی با رویکرد تیر پیوند
استفاده از سیستم دیوار برشی فولادی نسبت به بسیاری از سیستمهای مقاوم در برابر بارهای جانبی به لحاظ عملکردی و نیز اقتصادی مقرونبهصرفه است. علیرغم مزایای بسیار دیوارهای برشی فولادی، این سیستم بهصورت گسترده مورد استفاده قرار نگرفته است. برخی از دلایل کمتوجهی شامل عدم شناخت صحیح رفتار سیستم و بزرگی قابلتوجه مقاطع ستونهای اطراف دیوار نسبت به دیوار برشی بتنی میباشد.هدف این تحقیق بهبود رفتار سیستم تعریف شده فوق با بهرهگیری از رفتار برشی ورق و ستونهای فرعی پیرامون آن و استفاده از ظرفیت حداکثر سیستم است. در این تحقیق ورق و ستونهای فرعی مانند تیر پیوند در سیستمهای مهاربند واگرا در نظر گرفته شده است که ورق پرکننده و ستونهای فرعی پیرامون آن بهترتیب نقش جان و بال تیر پیوند را بازی میکنند. بدینمنظور نمونههای مختلف در نرمافزار اجزای محدود مدلسازی و رفتار چرخهای آنها بررسی میگردد. نتایج نشان میدهد استفاده از این سیستم با رویکرد ذکر شده در قابهای فولادی در مقایسه با دیوارهای برشی فولادی باعث افزایش جذب انرژی و سطح زیر منحنیهای هیسترزیس و نیز کاهش پدیده باریکشدگی منحنی میشود. از جمله دیگر مزایای این سیستم میتوان به کاهش قابلتوجه تقاضا در ستونها، قابلیت انطباق با معماری، منحنیهای چرخهای پایدار، عدم تأثیر سیستم ارائه شده در رفتار اتصالات تیر به ستون و در نتیجه عدم نیاز به اتصالات خمشی، قابلیت استفاده در ساختمانهای بلندمرتبه و همچنین قابلیت استفاده در بهسازی لرزهای ساختمانها اشاره نمود.
http://www.bese.ir/article_240414_4923538469826b46dca3563b739be390.pdf
2019-12-22
75
85
دیوار برشی فولادی نیمه مقید در لبه
رفتار چرخهای
باریکشدگی
تیر پیوند برشی
بار چرخهای
حدیث
محمدمرادی
h.mohammadmoradi@iiees.ac.ir
1
پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
LEAD_AUTHOR
بهرخ
حسینی هاشمی
behrokh@iiees.ac.ir
2
پژوهشکده مهندسی سازه، پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
AUTHOR
محمدعلی
جعفری صحنه سرایی
3
پژوهشگاه نیرو، تهران، ایران
AUTHOR
Tromposch, E.W. and Kulak, G.L. (1987) Cyclic and Static Behaviour of Thin Panel Steel Plate Shear Walls. Department of Civil Engineering, University of Alberta, Edmonton, Structural Engineering Report No. 145, Apr. 1987, 158p.
1
Berman, J., Lowes, L., Okazaki, T., Bruneau, M., Tsai, K., Driver, R.G., Sabelli, R. and Moore, W.P. )2008( Research Needs and Future Directions for Steel Plate Shear Walls. ASCE.
2
Xue, M. and Lu, L-W. (1994) Interaction of Steel Shear Panels with Surrounding Frame Members. Proceedings of the Structural Stability Research Council Annual Technical Session, Bethlehem, PA, 339-354.
3
Driver, R.G., Gilbert, G.Y., Behbahanifard, M.R. and Hussain, M.A. (2001) Recent Development and Future Directions in Steel Plate Shear Wall Research. Proceeding of North American Steel Construction Conference, Ft. Lauderdale, FL, May 9-12.
4
Moharrami, H., Habibnejad, A., Mazrouei, A. and Alizadeh, H. (2005) Semi-Supported Thin Steel Shear Walls. research project no. 1â4679, The Building and Housing Research Centre.
5
Guo, L., Rong, Q., Ma, X. and Zhang, S. (2011) Behavior of steel plate shear wall connected to frame beams only. International Journal of Steel Structures, 11(4), 467-479.
6
Pirmoz, A. (2012) Beamâattached steel plate shear walls. The Structural Design of Tall and Special Buildings, 21(12), 879-895.
7
Jahanpour, A., Johnson, J. and Moharrami, H. (2012) Seismic behavior of semi-supported steel shear walls. Journal of Constructional Steel Research, 74, 118-133.
8
Clayton, P.M., Berman, J.W. and Lowes, L.N. (2015) Seismic performance of self-centering steel plate shear walls with beam-only-connected web plates. Journal of Construction Steel Research, 106, 198-208.
9
Shekastehband, B., Azarakhsh, A.A. and Pavir, A. (2017) Behavior of semi-supported steel shear walls: Experimental and numerical simulations. Engineering Structures, 135, 161-176.
10
ANSI/AISC 341-10. (2005) Seismic Provisions for Structural Steel Buildings.
11
Venture, S.J. (1997) Protocol for fabrication, inspection, testing, and documentation of beam-column connection tests and other experimental specimens. Rep. No. SAC/BD-97, 2.
12
ORIGINAL_ARTICLE
ارزیابی عملکرد سازههای قاب خمشی فولادی متوسط و ویژه تحت آتش پس از زلزله
زلزلههای شدید ممکن است باعث وقوع آتشسوزیهای گسترده در سازهها شوند. در شرایط پس از زلزله عواملی چون بروز تغییر مکانهای پسماند در طبقات سازه، افزایش شدت آتش و آسیبدیدگی پوششهای ضد حریق مقاومت سازه را در برابر آتش کاهش میدهد. روش و الزامات طراحی لرزهای سازهها میتواند تأثیر زیادی بر مقاومت آنها در برابر آتش داشته باشد. در این مقاله، عملکرد سازههای قاب خمشی فولادی متوسط و ویژه تحت آتش پس از زلزله مورد مقایسه قرار میگیرد. برای این منظور، دو قاب خمشی فولادی 5 و 10 طبقه با پوشش ضد حریق در دو حالت ویژه و متوسط طراحی شده و تحت بارگذاری آتش استاندارد و آتش طبیعی در شرایط پس از زلزله قرار میگیرند. برای بارگذاری لرزهای، دو سطح خطر زلزله طرح و زلزله خیلی شدید در نظر گرفته شده است. بر اساس نتایج بهدستآمده، کاهش زمان مقاومت نمونههای قاب خمشی ویژه ناشی از اعمال بارهای لرزهای با هر دو سطح خطر طرح کمتر از 21 درصد است. درحالیکه زلزلههای خیلی شدید باعث کاهش 75 درصدی در زمان مقاومت سازههای قاب خمشی متوسط میشوند، کاهش مقاومت این سازهها در مقابل زلزله طرح کمتر از 19 درصد برآورد شده است. همچنین، نتایج تحلیلها نشان میدهد که زلزلههای خیلی شدید ممکن است باعث خرابی قابهای خمشی متوسط تحت آتش طبیعی پس از زلزله شوند، درحالیکه قابهای خمشی ویژه قادر به تحمل بار آتش طبیعی در شرایط پس از زلزله میباشند.
http://www.bese.ir/article_240415_a76c45d6a6954633904b3b610177e693.pdf
2019-12-22
87
106
آتش پس از زلزله
آتش استاندارد
آتش طبیعی
سطوح عملکردی
قاب خمشی فولادی
محسن
گرامی
mgerami@semnan.ac.ir
1
دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران
LEAD_AUTHOR
پوریا
میرزایی
2
دانشگاه سمنان، سمنان، ایران
AUTHOR
Cousins, W., et al. (2002) Modelling the spread of post-earthquake fire in Wellington City. Proc. The 2002 Technical Conference and AGM. New Zealand Society for Earthquake Engineering, Napier.
1
Buchanan, A. H. (2001) Fire engineering design guide. Centre for advanced Engineering, University of Canterbury.
2
Mousavi, S., Bagchi, A. and Kodur, V. K. (2008) Review of post-earthquake fire hazard to building structures. Canadian Journal of Civil Engineering, 35(7), 689-698.
3
Nishino, T., Tanaka, T. and Hokugo, A. (2012) An evaluation method for the urban post-earthquake fire risk considering multiple scenarios of fire spread and evacuation. Fire safety journal, 54, 167-180.
4
Della Corte, G., Landolfo, R. and Mazzolani, F. (2003) Post-earthquake fire resistance of moment resisting steel frames. Fire Safety Journal, 38(7), 593-612.
5
Faggiano, B. (2007) Fire after earthquake. Proc. WG1 Meeting on Urban Habitat Constructions under Catastrophic Event. Prague.
6
Faggiano, B., De Gregorio, D. and Mazzolani, F. (2010) Assessment of the robustness of structures subjected to fire following earthquake through a performance-based approach. Proc. Conference Urban habitat constructions under catastrophic events (COST C26 Action). Naples, Italy.
7
Zaharia, R. and Pintea, D. (2009) Fire after earthquake analysis of steel moment resisting frames. International Journal of Steel Structures, 9(4), 275-284.
8
Behnam, B. and Ronagh, H. R. (2014) Behavior of momentâresisting tall steel structures exposed to a vertically traveling postâearthquake fire. The Structural Design of Tall and Special Buildings, 23(14), 1083-1096.
9
Behnam, B. and Ronagh, H. R. (2015) Post-Earthquake Fire performance-based behavior of unprotected moment resisting 2D steel frames. KSCE Journal of Civil Engineering, 19(1), 274-284.
10
Memari, M., Mahmoud, H. and Ellingwood, B. (2014) Post-earthquake fire performance of moment resisting frames with reduced beam section connections. Journal of Constructional Steel Research, 103, 215-229.
11
Elhami Khorasani, N., Garlock, M. and Gardoni, P. (2016) Probabilistic performance-based evaluation of a tall steel moment resisting frame under post-earthquake fires. Journal of Structural Fire Engineering, 7(3), 193-216.
12
Behnam, B. (2016) Structural response of vertically irregular tall momentâresisting steel frames under preâand postâearthquake fire. The Structural Design of Tall and Special Buildings, 25(12), 543-557.
13
Leo Braxtan, N. and Pessiki, S. (2011) Bond performance of SFRM on steel plates subjected to tensile yielding. Journal of fire protection engineering, 21(1), 37-55.
14
Keller, W.J. and Pessiki, S. (2012) Effect of earthquake-induced damage to spray-applied fire-resistive insulation on the response of steel moment-frame beam-column connections during fire exposure. Journal of fire protection engineering, 22(4), 271-299.
15
Standard No. 2800 (2015) Building &Housing Research Center. Iranian Code of Practice for Seismic Resistant Design of Buildings. Iran.
16
Ministry of roads and Urban Development, (2013) Iranian National Building Code for Steel Structures-Part 10. Tehran.
17
Quiel, S.E. and M.E. Garlock, M.E. (2008) Modeling high-rise steel framed buildings under fire. Proc. Structures Congress 2008. Crossing Borders.
18
Underwriters' Laboratories (1992) Fire Resistance Directory. Vol. 1.
19
Toh, W., Tan, K. and Fung, T. (2001) Strength and stability of steel frames in fire: Rankine approach. Journal of Structural Engineering, 127(4), 461-469.
20
Charney, F. A. and Marshall, J. (2006) A comparison of the Krawinkler and scissors models for including beam-column joint deformations in the analysis of moment-resisting steel frames. Engineering journal American institute of steel construction, 43(1), 31-48.
21
EN 1993-1-2 (2005) European standard. Eurocode 3: Design of steel structures, Part 1-2: Structural fire design. CEN, Brussels, Belgium.
22
Rubert, A. and Schaumann, P. (1986) Structural steel and plane frame assemblies under fire action. Fire Safety Journal, 10(3), 173-184.
23
Lien, K., Chiou, Y., Wang, R. and Hsiao, P. (2010) Vector form intrinsic finite element analysis of nonlinear behavior of steel structures exposed to fire. Engineering Structures, 32(1), 80-92.
24
Sun, R., Huang, Z. and Burgess, I. W. (2012) Progressive collapse analysis of steel structures under fire conditions. Engineering Structures, 34, 400-413.
25
Memari, M. and Mahmoud, H. (2014) Performance of steel moment resisting frames with RBS connections under fire loading. Engineering Structures, 75, 126-138.
26
FEMA440 (2005) Federal Emergency Management Agency. Improvement of nonlinear static seismic analysis procedures. Washing- ton, DC, USA.
27
A.S.o.C. (2007) ASCE Publications. Seismic rehabilitation of existing buildings. Vol. 41.
28
EN 1991-1-2 (2002) European standard. Eurocode 1: Action on structures, Part 1-2: Action on structures exposed to fire. CEN, Brussels, Belgium.
29
Cadorin, J.F., Pintea, D., Dotreppe, J.C. and Franssen, J.M. (2003) A tool to design steel elements submitted to compartment firesâOZone V2. Part 2: Methodology and application. Fire Safety Journal, 38(5), 429-451.
30
Liu, T., Fahad, M. and Davies, J. (2002) Experimental investigation of behaviour of axiallyrestrained steel beams in fire. Journal of Constructional Steel Research, 58(9), 1211-1230.
31
ORIGINAL_ARTICLE
ضریب اصلاح m برای میانقابهای با و بدون بازشو بر اساس اطلاعات آزمایشگاهی
میانقاب، دیواری است که در داخل و در تماس کامل با قاب اجرا میشود و سختی و مقاومت آن را به مقدار قابلملاحظهای افزایش میدهد. در آییننامههای بهسازی لرزهای توصیه شده پس از بررسی کفایت اعضا و اتصالات قاب برای تحمل نیروهای حاصل از کنش میانقابی، وجود میانقاب با یک دستک فشاری قطری مدلسازی گردد. در مورد میانقابهای دارای بازشو نیز رویه مشابهی بهکار گرفته میشود و در آییننامههای بهسازی استفاده از ظرفیت آنها مجاز دانسته شده است. این در حالی است که برای مدلسازی آنها در سازه لازم است علاوه بر ارائه مدل ریاضی، مقدار ضریب اصلاح (m) ارائه گردد که در حال حاضر پیشنهادی برای هریک از این موارد وجود ندارد. بنابراین در این تحقیق تلاش شده است که مقدار ضریب اصلاح بر اساس کارهای آزمایشگاهی موجود در ادبیات فنی ارائه گردد. برای این منظور، مقدار این ضریب برای نمونههای دارای بازشو و همچنین نمونههای مشابه توپر محاسبه و با یکدیگر مقایسه شده است. در انتها، نشان داده شده است که ضریب اصلاح m برای میانقابهای دارای بازشو را میتوان برابر با مقدار متناظر میانقاب فاقد بازشو در نظر گرفت.در ادامه ضریب اصلاح میانقابهای توپر مورد توجه قرار گرفت. عوامل مؤثر بر ضریب اصلاح اینگونه میانقابها بررسی و نشان داده شد که ضریب اصلاح اینگونه میانقابها فقط تابع جنس میانقاب و قاب پیرامون آن است و بهرغم پیشنهاد آییننامهها، به نسبت بعدی و نسبت مقاومت قاب به میانقاب وابسته نیست. در ادامه مقادیری برای ضریب m میانقاب توپر برحسب جنس قاب و میانقاب پیشنهاد شد.
http://www.bese.ir/article_240405_174038f77ffbe859e5d8249ccc4dfd45.pdf
2019-12-22
107
119
ضریب اصلاح
منحنی پشتواره
منحنی پوش
میانقابهای دارای بازشو
قاب میانپر
مجید
محمدی
m.mohammadigh@iiees.ac.ir
1
پژوهشکده مهندسی سازه، پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
LEAD_AUTHOR
علیرضا
سرمایه خواه
2
مؤسسه آموزش عالی آیندگان، تنکابن، ایران
AUTHOR
Office of Deputy for Strategic Supervision Department of Technical Affairs (2014) Instruction for Seismic Rehabilitation of Existing Buildings. No. 360, (in persian).
1
ASCE/SEI Seismic Rehabilitation Standards Committee (2007) Seismic rehabilitation of existing buildings (ASCE/SEI 41-06). American Society of Civil Engineers, Reston, VA.
2
ASCE/SEI Seismic Rehabilitation Standards Committee (2013) Seismic rehabilitation of existing buildings (ASCE/SEI 41-13). American Society of Civil Engineers, Reston, VA.
3
Mohammadi, M. (2017) Influences of Infills on Building Structures, Sharif University Press (in Persian).
4
Holmes, M. (1961) Steel frames with brickwork and concrete infilling. Proceedings of the Institution of Civil Engineers. 19(4), 473-478.
5
Mallick, D. and Garg, R. (1971) Effect of openings on the lateral stiffness of infilled frames. Proceedings of the Institution of Civil Engineers, 49(2), 193-209.
6
Mosalam, K.M., White, R.N. and Gergely, P. (1997) Static response of infilled frames using quasi-static experimentation. Journal of Structural Engineering, 123(11), 1462-4169.
7
Polyakov, S. and Cairns, G. (1956) Masonry in Framed Buildings.
8
Ghazimahalleh, M.M. (2007) Stiffness and damping of infilled steel frames. Proceedings of the Institution of Civil Engineers-Structures and Buildings. 160(2), 105-118.
9
Kakaletsis, D. and Karayannis, C. (2008) Influence of masonry strength and openings on infilled R/C frames under cycling loading. Journal of Earthquake Engineering, 12(2), 197-221.
10
Al-Chaar, G. (2002) Evaluating Strength and Stiffness of Unreinforced Masonry Infill Structures. DTIC Document.
11
Kakaletsis, D. and Karayannis, C. (2007) Experimental investigation of infilled R/C frames with eccentric openings. Structural Engineering and Mechanics. 26(3), 231-250.
12
Kakaletsis, D.J. and Karayannis, C.G. (2009) Experimental investigation of infilled reinforced concrete frames with openings. ACI Structural Journal, 106(2), 132.
13
Tasnimi, A. and Mohebkhah, A. (2011) Investigation on the behavior of brick-infilled steel frames with openings, experimental and analytical approaches. Engineering Structures, 33(3), 968-980.
14
Sigmund, V. and Penava, D. (2012) Experimental study of masonry infilled R/C frames with opening. 15th World Conference on Earthquake Engineering.
15
Dawe, J. and Seah, C. (1989) Behaviour of masonry infilled steel frames. Canadian Journal of Civil Engineering, 16(6), 865-876.
16
Mehrabi, A.B., et al. (1996) Experimental evaluation of masonry-infilled RC frames. Journal of Structural Engineering, 122(3), 228-237.
17
Imran, I. and Aryanto, A. (2009) Behavior of reinforced concrete frames in-filled with lightweight materials under seismic loads. Civil Engineering Dimension, 11(2), 69-77.
18
Sevil, T. and Canbay, E. (2010) Seismic strengthening of masonry infilled reinforced concrete frames with steel fiber reinforcement. Proceedings of the 9th US National and 10th Canadian Conference on Earthquake Engineering.
19
Altın, S., et al. (2010) Strengthening masonry infill walls with reinforced plaster. Proceedings of the Institution of Civil Engineers-Structures and Buildings, 163(5), 331-342.
20
Misir, S., et al. (2012) Experimental work on seismic behavior of various types of masonry infilled RC frames. Structural Engineering and Mechanics. 44(6), 763-774.
21
Kaltakci, M.Y., Koken, A. and Korkmaz, H.H. (2008) An experimental study on the behavior of infilled steel frames under reversed-cycling loading. Iranian Journal of Science and Technology, 32(B2), 157.
22
Flanagan, R.D. and Bennett, R.M. (1999) Bidirectional behavior of structural clay tile infilled frames. Journal of Structural Engineering, 125(3), 236-244.
23
Parsa, F. and Moghadam, A.S. (2008) Experimental Investigation of Masonry Infilled Reinforced Concrete Frame. 681-690.
24
Puglisi, M., Uzcategui, M. and Florez-Lopez, J. (2009) Modeling of masonry of infilled frames, Part I: The plastic concentrator. Engineering Structures. 31(1), 113-118.
25
ORIGINAL_ARTICLE
مقایسه میراگرهای ویسکوز و هیسترزیس در کاهش آسیبپذیری لرزهای ساختمانهای فولادی بر اساس تقسیم اسکلت ساختمان به دو بخش داخلی و خارجی دارای اندرکنش دینامیکی
برای جلوگیری از پیامدهای نامطلوب ناشی از طراحی بر اساس آییننامههای متداول از جمله آوارگی هزاران نفر و لزوم تخریب و بازسازی ساختمان، طراحی سازه بهصورت تعمیرپذیر با کمک جاذبهای انرژی مورد توجه قرار گرفته است و در این راستا اخیراً توسط نویسندگان مقاله تقسیم سازه ساختمان به دو بخش داخلی و خارجی با پریودهای مختلف و استفاده از میراگرهای هیسترزیس با مشخصات مناسب بین آن دو بخش بهمنظور استهلاک انرژی مورد بررسی قرار گرفته است. در پژوهش حاضر برای استهلاک انرژی از میراگرهای ویسکوز بین دو بخش سازه استفاده شده و مکان و ضریب میرایی مناسب میراگرها تعیین و پاسخهای سازه با نتایج حاصل از بهکارگیری میراگرهای هیسترزیس با سختی، مقاومت و قابلیت جذب انرژی مناسب مقایسه شده است. برای این منظور ابتدا با تقسیم یک ساختمان 5 طبقه به دو بخش و استفاده از مستهلککنندههای ویسکوز در تراز بام ضمن تشکیل معادلات حرکت و کدنویسی در محیط برنامه MATLAB به تعیین ضریب میرایی مناسب میراگر ویسکوز پرداخته شد و نتایج نشان داد که با انتخاب مقادیر مناسب برای این کمیّت میتوان باعث جذب انرژی بالا و کاهش قابل ملاحظه دریفت طبقات ساختمان گردید. سپس سه ساختمان فولادی مهاربندی شده 5، 8 و 11 طبقه به کمک نرمافزار ETABS طراحی و به دو بخش داخلی و خارجی تقســیم و در نرمافزار PERFORM-3D مدل شد و در آنها از میراگر ویسکوز با ضریب میرایی مناسب حاصل از نرمافزار MATLAB استفاده گردید. از مقایسه عملکرد میراگر ویسکوز با ضریب میرایی مناسب و میراگر هیسترزیس، با سختی و مقاومت مناسب، مشخص شد در حالتی که از میراگرهای ویسکوز با ضریب میرایی مناسب استفاده شود ماکزیمم دریفت طبقه در سازه خارجی تقریباً 35 درصد و در سازه داخلی تقریباً 50 درصد نسبت به سازه یکپارچه کاهش مییابد. این در حالی است که اگر از میراگر هیسترزیس با سختی و مقاومت مناسب استفاده شود ماکزیمم دریفت طبقه نسبت به سازه یکپارچه، در سازه خارجی تقریباً 20 درصد و در سازه داخلی تقریباً 65 درصد کاهش مییابد.
http://www.bese.ir/article_240407_9b7e5ba93dfd6ec4136c7f337787d15a.pdf
2019-12-22
121
134
هدایت آسیب
مستهلککننده های هیسترتیک و ویسکوز
تحلیل دینامیکی غیرخطی
MATLAB
PERFORM-3
عباس
طاهری
1
گروه مهندسی عمران، واحد اراک، دانشگاه آزاد اسلامی، اراک، ایران
AUTHOR
محمود
حسینی
hosseini@iiees.ac.ir
2
پژوهشکده مهندسی سازه، پژوهشگاه بین المللی زلزله شناسی و مهندسی زلزله، تهران، ایران
LEAD_AUTHOR
عبدالرضا
سروقد مقدم
moghadam@iiees.ac.ir
3
پژوهشکده مهندسی سازه، پژوهشگاه بین المللی زلزله شناسی و مهندسی زلزله، تهران، ایران
AUTHOR
Ziyaiefar, M. (2006) Vertical seismic isolation method in steel structures against earthquake. 6th International Conference on Seismology and Earthquake Engineering, International Institute of Seismology and Earthquake Engineering, pp. 1611-1620.
1
Hejazi, F., Dalili, M. (2010) Coupling Parallel Buildings by Supplemental Viscous Damper Device. Proceedings of the International Conference on Computing in Civil and Building Engineering, pp. 361-370.
2
Wijaya, M., Yamao, T. (2013) Seismic Performance Investigation of the Folded Cantilever Shear Structure. International Journal of Civil Engineering and Technology, pp. 145-153.
3
Abdelraheem Farghaly, A. (2014) Optimization of Viscous Dampers with the Influence of Soil Structure Interaction on Response of Two Adjacent Buildings under seismic load. IOSR Journal of Engineering, pp. 18-27.
4
Annapurna, V., Vankudre, S. (2014) Vibration Control of Adjacent Buildings Connected with Selected Types of Dampers, International Journal of Engineering Research & Technology (IJERT), pp. 1431-1436.
5
Jamshidi, J., Hosseini, M. (2015) Dividing the building structure into two parts with dynamic interaction. 2nd International Conference on Earthquake Resistant Cityâ, pp. 352-360.
6
Bougteb, Y., Ray, T. (2018) Choice between series and parallel connections of hysteretic system and viscous damper for seismic protection of structures. Journal of Earthquake Engineering & Structural Dynamics, pp. 352-360.
7
Taheri, A., Hosseini, M. and Moghadam, A.S. (2018) Creation of innovative earthquake resistant steel buildings by dividing the structure into inner and outer parts having interaction by hysteretic dampers. JVE International Ltd. Journal of Vibroengineering, pp. 477-493.
8
Taheri, A. (2017) Dividing the Buildingâs Skeleton into Two Inner and Outer Interactive Parts and Using Yielding Dampers between them for Seismic Response Reduction. Ph.D. Dissertation submitted to Dept. of Civil Eng., Arak Branch of the Islamic Azad University, Arak, Iran.
9
Iranian Code Of Practice For Seismic Resistant Design Of Buildings (2015) Standard No. 2800 4th edition.
10
Federal Emergency Management Agency (2006) Pre-standard and Commentary for the Seismic Rehabilitation of Buildings, FEMA-356.
11
American Building Society of Civil Engineers (2010) Minimum design loads for buildings and other structures.
12
ATC-40, Applied Technology Council (1998) California Seismic Safety Commission.
13
ORIGINAL_ARTICLE
ارزیابی رفتار لرزهای سازههای فولادی مجهز به میراگر MADAS در مقایسه با سیستم قاب خمشی
هدف از این مقاله ارزیابی مشخصات میراگر ADAS اصلاح شده و عملکرد لرزه ای سازه های فولادی کوتاه و میان مرتبه مجهز به این نوع میراگر می باشد. ورق های X شکل مورد استفاده در میراگر ADAS اصلاح شده (MADAS) به گونه ای قرار گرفتهاند که علیرغم مقید نمودن درجات آزادی چرخشی در دو انتها، تغییر مکان آنها در امتداد قائم کاملاً آزاد است و در نتیجه هیچگونه نیروی محوری در میراگر ایجاد نمی شود. بدینترتیب، رفتار ورقها تحت نیروهای جانبی کاملاً خمشی بوده و از سوی دیگر بارهای ثقلی طبقات یا مؤلفه قائم در تیرها و بادبندها نیز کوچکترین تأثیری در رفتار میراگر جدید ندارند. در این مقاله مدل عددی میراگر به منظور صحت سنجی نتایج مدل عددی با مدل آزمایشگاهی ایجاد شده است. در ادامه عملکرد لرزه ای سازه های مجهز به میراگر MADAS به وسیله مدلسازی عددی بررسی و پارامترهای لرزه ای از قبیل ضریب رفتار، میرایی معادل و جابجایی نسبی طبقات برآورد شده است. نتایج حاصل بیانگر رفتار برتر سازه های مجهز به میراگر MADAS در مقایسه با سازه های خمشی متوسط بوده است. همچنین مطالعات رفتار چرخ های میراگر یاد شده در مقایسه با میراگرهای رقیب (مانند ADAS و TADAS) رفتار مناسب تری را نشان داده است.
http://www.bese.ir/article_240408_298a94083175a74f338ab99a9c48b680.pdf
2019-12-22
135
152
میراگر فلزی تسلیمشونده
قاب خمشی
ضریب رفتار
میرایی معادل
تغییر مکان نسبی طبقات
محمدقاسم
وتر
vetr@iiees.ac.ir
1
پژوهشکده مهندسی سازه، پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
LEAD_AUTHOR
عباس
شفیع زاده
a_shafizadeh@iiees.ac.ir
2
پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
AUTHOR
ابوالفضل
ریاحی نوری
abriahi@yahoo.com
3
گروه مهندسی عمران، دانشکده هنر و معماری، واحد تهران غرب، دانشگاه آزاد اسلامی، تهران، ایران
AUTHOR
Soong, T.T. and Dargush, G.F. (1997) Passive Energy Dissipation Systems in Structural Engineering. Wiley.
1
Stiemer, S. and Godden, W.G. (1980) Shaking Table Tests of Piping Systems with Energy Absorbing Restrainers. Vol. 4. University of California Earthquake Engineering Research Center.
2
Scholl, R.E. (1988) Added damping and stiffness elements for earthquake damage and loss control. in Proceedings of Conference XLI: A Review of Earthquake Research Applications in the National Earthquake Hazards Reduction Program: 1877-1987.
3
Bergman, D.M. and Goel, S.C. (1987) Evaluation of Cyclic Testing of Steel-Plate Devices for Added Damping and Stiffness. Department of Civil Engineering, University of Michigan.
4
Xia, C. and Hanson, R.D. (1992) Influence of ADAS element parameters on building seismic response. Journal of Structural Engineering, 118(7), 1903-1918.
5
Whittaker, A. (1989) Earthquake Simulator Testing of Steel Plate Added Damping and Stiffness Elements. Earthquake Engineering.
6
Tsai, K.-C., Chen, H.-W., Hong, C.-P., & Su, Y.-F. (1993) Design of Steel Triangular Plate Energy Absorbers for SeismicâResistant Construction. Earthquake Spectra, 9(3), 505-528.
7
Mahmoudi, M. and Abdi, M.G. (2012) Evaluating response modification factors of TADAS frames. Journal of Constructional Steel Research, 71, 162-170.
8
Moghaddasi, M. and Namazi, A. (2016) Assessment of Performance of TADAS Dampers for the Seismic Rehabilitation of Buildings. International Journal of Applied Engineering Research, 11(21), 10516-10523.
9
Moreschi, L.M. and Singh, M.P. (2003) Design of yielding metallic and friction dampers for optimal seismic performance. Earthquake Engineering & Structural Dynamics, 32(8), 1291-1311.
10
Apostolakis, G. and Dargush, G.F. (2010) Optimal seismic design of moment-resisting steel frames with hysteretic passive devices. Earthquake Engineering & Structural Dynamics, 39(4), 355-376.
11
Hao, L. and Zhang, R. (2016) Structural safety redundancy-based design method for structure with viscous dampers. Struct Eng Mech., 59(5), 821-840.
12
Hao, L., Zhang, R., and Jin, K. (2018) Direct design method based on seismic capacity redundancy for structures with metal yielding dampers. Earthquake Engineering & Structural Dynamics, 47(2), 515-534.
13
Khaleghian, F. and Tehranizadeh, M. (2007) Laboratory Study of New Metal Dampers Applying X-Shape Plate. 5th International Conference on Seismology and Earthquake Engineering, Tehran (in Persian).
14
ASCE (2010) Minimum Design Loads for Buildings and Other Structures, ASCE/SEI. American Society of Civil Engineers.
15
BHRC (2007) Standard No. 2800 Iranian Code of Practice for Seismic Resistant Design of Buildings. 4th ed. Building and Housing Research Center (in Persian).
16
Miranda, E. and Bertero, V.V. (1994) Evaluation of Strength Reduction Factors for EarthquakeâResistant Design. Earthquake Spectra, 10(2), 357-379.
17
Abdi, M.G. (2011) Evaluating Function of ADAS Yielding Damper in Controling Seismic Behavior of Structures. Master Thesis, Shahid Rajaee Univesity, Tehran (in Persian).
18
Mahmoudi, M., Mirzaei, A., and Vosough, S. (2013) Evaluating equivalent damping and response modification factors of frames equipped by pall friction dampers. Journal of Rehabilitation in Civil Engineering, 1(1), 78-92.
19
Krawinkler, H. (1992) Guidelines for Cyclic Seismic Testing of Components of Steel Structures. Applied Technology Council, Redwood City, Calif.
20
Lemaitre, J. and Chaboche, J.-L. (1994) Mechanics of Solid Materials. Cambridge university press.
21
Budahazy, V. (2015) Uniaxial Cyclic Steel Behavior and Model for Dissipative Structures. Ph.D. Thesis, Structural Engineering, Budapest University of Technology and Economics,
22
Armstrong, P.J. (1966) A mathematical representation of the multiaxial Bauschinger effect. CEBG Report RD/B/N, 731.
23
Instruction for Seismic Rehabilitation of Existing Buildings, No 360. Islamic Republic of Iran Management and Planning Organization (in Persian).
24
Tasnimi, A. and Masoumi, A. (2005) Calculation Response Modification Factor of Concrete Moment Resistant Frames. Building and Housing Research Center (in Persian).
25
ORIGINAL_ARTICLE
بررسی عملکرد سیستم قاب خمشی و دیوار گهوارهای با استفاده از تحلیل دینامیکی غیرخطی فزاینده (IDA)
سیستمهای مقاوم جانبی متداول از طریق توزیع خرابی بین المانهای سازهای اولیه و دریفت پسماند، انرژی را مستهلک میکنند که این باعث خسارات اجتماعی- اقتصادی فراوان ناشی از هزینههای تعمیر و صرف زمان پس از رخداد زلزله میشود. دیوارهای گهوارهای با آزادکردن قید چرخشی پای دیوار در طی رخداد زلزله بهصورت گهوارهای روی فونداسیون حرکت کرده و با بازگرداندن سازه متصل به خود به موقعیت اولیه دریفت پسماند را کاهش میدهند. در این تحقیق رفتار قاب خمشی بتن مسلح با دیوار گهوارهای تحت تحلیل دینامیکی غیرخطی فزاینده بهصورت دو بعدی با نرمافزار سپ در دو مدل 5 طبقه و10 طبقه بررسی و پاسخ سازه با پاسخ قاب خمشی متناظر با دیوار برشی متداول مقایسه شد. نتایج نشان داد دیوار گهوارهای در هر دو مدل 5 و10 طبقه باعث کاهش قابلتوجه دریفت پسماند شده و با مجهز کردن آن به کابلهای پس کشیده و میراگر در مدل10 طبقه، میتوان از رفتار اجزای غیر سازهای به هنگام زلزله اطمینان حاصل کرد. اتصال قاب به دیوار نیز در مدلهای مختلف بررسی و اتصال مفصلی قاب به دیوار برای رفتار بهتر سیستم گهوارهای مناسب ارزیابی شد.
http://www.bese.ir/article_240409_baf5c3bcef4fc038ad8ce6eebbdbf3d4.pdf
2019-12-22
153
168
سیستم دوگانه خودمحور
دیوار گهوارهای
دریفت پسماند
تحلیل IDA
نادر
خواجه احمد عطاری
n.attari@bhrc.ac.ir
1
مرکز تحقیقات راه و مسکن و شهرسازی، تهران، ایران
AUTHOR
زهرا
رحیمی سجاسی
zahra.rahimi@bhrc.ac.ir
2
پژوهشکده مسکن، مرکز تحقیقات راه و مسکن و شهرسازی، تهران، ایران
LEAD_AUTHOR
- Wiebe, L. (2008) Mitigation of Higher Mode Effects in Self-Centering Walls by Using Multiple Rocking Sections. An Individual Study Submitted for the Master Degree. University of Pavia.
1
- Wada, A. (2012) Pin-supported walls for enhancing the seismic performance of building structures. Earthquake Engineering & Structural Dynamics, 41, 2075-2091.
2
- Filiatrault, A. (2004) Development of Self-Centering Earthquake Resisting Systems. 13th World Conference on Earthquake Engineering. Vancouver, B.C., Canada, Paper No. 3393.
3
- Wada, A. (2010) Seismic retrofit of existing SRC frame using rocking walls and steel dampers. Frontiers of Architecture and Civil Engineering in China. 5(3), 259-266.
4
- Makris, N. and Aghagholizadeh, M. (2017) The dynamics of an elastic structure coupled with a rocking wall. EARTHQUAKE ENGINEERING & STRUCTURAL DYNAMICS, 46, 945â962. DOI: 10.1002/eqe.2838
5
- Zibaei, H and Mokari, J. (2014). Evaluation of seismic behavior improvement in RC MRFs retrofitted by controlled rocking wall systems. The Structural Design of Tall and Special Buildings, 23, 995-1006, DOI: 10.1002/tal.1101.
6
- Grigorian, C.E and Grigorian, M. (2015) Performance Control and Efficient Design of Rocking-Wall Moment Frames. Journal of Structural Engineering, DOI: 10.1061/(ASCE)ST.1943-541X.0001411.
7
- Henry, S.R. (2016) Residual drift analyses of realistic self centering concrete wall systems. Earthquakes and Structures, DOI: 10.12989/eas.2016.10.2.409.
8
- Qingzhi, L. (2016) Study on Interaction between Rocking-Wall System and Surrounding Structure. A Dissertation for the Degree Ofdoctor of Philosophy, University Of Minnesota.
9
- ACI (2008) Building Code Requirements for Structural Concrete (ACI 318-08) and Commentary. ACI Committee 318, Farmington Hills, MI.
10
- Saqayean, A. and Nateghi, E.F. (2010) Comparison of different modeling methods in predicting nonlinear behavior of shear walls. Journal of Seismology and Earthquake Engineering, International Institute of Earthquake Engineering and Seismology, Tehran (in Persian).
11
- SAP2000, version 14.00 (Copyright 1976-2009) A product of Computers and Structures (1995) University Ave, Berkeley, California.
12
- Hashemian, B. (2014) Study on the influence of post-tensioned cables on the behavior of steel rocking structures using pushover analysis. Second National Conference on Structural Engineering, Amirkabir University, Tehran (in Persian).
13
- Pars PBL Group [Online]. Available: www.parspblco.com/downloads/catalogue/catalogue.pdf [2017, October 17].
14
- Behsaz Andishan Tehran [Online]. Available: www.behsazandishan.com [2017, âNovember 2] (Personal Communication).
15
- Vamvatsikos, D. and Cornell, C.A. (2002) Incremental Dynamic Analysis. Earthquake Engng. Struct. Dyn.
16
- Grigorian , C.E. and Grigorian, M. (2016) An introduction to the structural design of rocking wall-frames with a view to collapse prevention, self-alignment and repairability. The Structural Design of Tall and Special Buildings, 25, 93â111, DOI: 10.1002/tal.1230.
17
ORIGINAL_ARTICLE
مدلسازی توزیع ساختمانهای مسکونی و جمعیت وابسته به آن با رویکرد داسیمتری در برآورد ریسک لرزهای شهری؛ مطالعه موردی: شهر ساری
مدلسازی توزیع ساختمانهای مسکونی و جمعیت وابسته به آن جزء لاینفک در تجزیهوتحلیل خطرپذیری مستقیم و غیرمستقیم مرتبط با سوانح طبیعی ازجمله زلزله در محیطهای شهری است. در این مطالعه، توزیع جمعیت مسکونی همبسته با بناهای مسکونی برآورد گردیده است. این پژوهش مدلی جامع با وضوح مکانی مناسب برای ایران، متناسب با شرایط منطقهای و در نظر گرفتن بانکهای اطلاعاتی موجود و قابلدسترس ارائه کرده است. روش داسیمتری، روشی کارا جهت توزیع مناسب دادههای موجود بهتناسب شرایط محیطی-منطقهای است که بر اساس نیازها و شرایط مورد نظر امکان تلفیق با دادههای رقومی کمکی را داشته و توسط مدلهای آماری توسعه مییابد. در این تحقیق، دادههای آماری (مرتبط با حوزهها و یا بلوکهای آماری- مرکز آمار) و تصاویر رقومی (شامل تصاویر ماهوارهای و دادههای مدل توزیع جمعیت جهانی لندسکن) گردآوری شده که پس از بررسی، پردازش و پالایش، ادغام دادهها صورت گرفت. همچنین شاخصهایی مهم و قابلاستخراج از تصاویر اپتیکی با وضوح بسیار بالا برای قسمتی از یک شهر معرفی شد که در تکمیل بانک اطلاعات ساختمان مفید میباشد. بهعنوان یک مطالعه موردی، خسارات لرزهای در قالب میزان تخریب ساختمانها و تلفات انسانی در منطقه مطالعاتی بررسیشده است. در گام اول، با هدف تکمیل و توسعه بانکهای اطلاعات محیط ساخته شده و برای دستیابی به پارسلهای ساختمانهای موجود، روشهای استخراج اشیاء (ساختمانها)[i]از تصاویر ماهوارهای در بلوکهای شهری مورد استفاده قرار گرفت. در فاز دیگر، اطلاعات سازهای و جمعیتی با رویکرد داسیمتری برای منطقه مورد نظر به دست آمدند و بانک اطلاعات با توزیع مکانی مناسب توسعه یافت. سپس، پهنهبندی حرکت توانمند زمین برای سناریوهای مطرح در منطقه مورد مطالعه تولید شد. در نهایت در گام آخر، برآورد میزان خسارات سازهای و تلفات انسانی مرتبط برحسب سناریوهای مورد نظر به دست آمد. در منطقه مطالعاتی، برآورد خسارات فیزیکی حاکی از این است که برای سناریوی مفروض زلزله گسل خزر بیش از 50000 واحد مسکونی در معرض تخریب شدید تا فروریزش خواهد بود.
http://www.bese.ir/article_240410_3471511fbff3c327bac434c69abcfc56.pdf
2019-12-22
169
179
ارزیابی آسیبپذیری
مدلسازی توزیع جمعیت
داسیمتری
سنجشازدور
برآورد خسارات و تلفات
بابک
منصوری
mansouri@iiees.ac.ir
1
پژوهشکده مدیریت خطرپذیری و بحران، پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
LEAD_AUTHOR
پرهام
جلیلوند
2
پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
AUTHOR
محسن
غفوری-آشتیانی
3
پژوهشکده مهندسی سازه، پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله، تهران، ایران
AUTHOR
Tavakoli, B., and Tavakoli, S. (1993) Estimating the Vulnerability and Loss Functions of Residential Buildings. Natural Hazards, 7(2), 155â171.
1
JICA-Japan International Cooperation Agency, 2000, The Study on Seismic Microzoning of the Greater Tehran Area in the Islamic Republic of Iran, Final Report, Main Report, SSF JR 00-186.
2
Hisada, Y., Shibayama, A., Ghayamghamian, M.R. (2005) Building Damage and seismic intensity in Bam city from the 2003 Bam, earthquake. Bull. Earthquake Research Inst. (ERI), 79, 81-93.
3
Mansouri, B., Ghafory-Ashtiany, M., Amini-Hosseini, K., Nourjou R. and Mousavi, M. (2010) Building Seismic Loss Model for Tehran. Earthquake Spectra, Journal of Earthquake Engineering Research Institute (EERI), 26(1), 153-168.
4
Mansouri, B., Kiani, A., and Amini-Hosseini, K. (2014) A Platform for Earthquake Risk Assessment in Iran â Case Studies: Tehran Scenarios and Ahar-Varzeghan Earthquake. Journal of Seismology and Earthquake Engineering, JSEE, 16(1).
5
Mansouri, B., and Amini-Hosseini, K. (2013) Global Earthquake Risk Model (GEM) - Earthquake Model of the Middle East Region (EMME) - Work Package 4: Seismic Risk Assessment. Final Report, 2013, IIEES internal contract #AM 7-269 (15/5/90).
6
Jonkman, S.N., Lentz, A., and Vrijling, J.K. (2010) A general approach for the estimation of loss of life due to natural and technological disasters. Reliab. Eng. Syst. Saf., 95(11), 1123â1133.
7
Chen, K., McAneney, J., Blong, R., Leigh, R., Hunter, L., and Magill, C. (2004) Defining area at risk and its effect in catastrophe loss estimation: a dasymetric mapping approach. Appl. Geogr., 24(2), 97â117.
8
Dent, B.D. (1996) Cartography: Thematic map design (4th ed.). Dubuque, IA: Wm. C. Brown Publishers.
9
Langford, M. and Unwin, D.J. (1994) Generating and mapping population density surfaces within a geographical information system. The Cartographic Journal, 31, 21â26.
10
Longley, P.A., Goodchild, M.F., Maguire, D.J., & Rhind, D.W. (2001) Geographic Information Systems and Science. Chichester: John Wiley & Sons.
11
Definiens Imaging (2004) e-Cognition 4.0, User Guide, Definiens Imaging GmbH, Munich, Germany.
12
Hessami-Azar, K. (2016) Personal Communication.
13
Hancilar, U., Tuzun, C., Yenidogan, C., and Erdik, M. (2010) ELER software- a new tool for urban earthquake loss assessment. Nat. Hazards Earth Syst. Sci., 10(12), 2677â2696.
14
Tatar, M., Jackson, J., Hatzfeld, D., & Bergman, E. (2007) The 2004 May 28 Baladeh earthquake (Mw 6.2) in the Alborz, Iran: overthrusting the South Caspian Basin margin, partitioning of oblique convergence and the seismic hazard of Tehran. Geophysical Journal International, 170(1), 249-261.
15
Grunthal, G. (Ed.) (1998) European Macroseismic Scale 1998, Cahiers du Centre Europeen de G´eodynamiqueet de S´eismologie. Conseil de lâEurope, Luxembourg.
16
Coburn, A. and Spence, R. (1992) Earthquake Protection, John Wiley & Sons.
17