پژوهشگاه بین المللی زلزله شناسی و مهندسی زلزله فصلنامه علوم و مهندسی زلزله 2476-6097 9 1 2022 03 21 Investigation of the Seismic Behavior of the Rehabilitated Steel Frames through Asymmetrically Weakening of the Beam بررسی رفتار لرزه ای قاب‌های فولادی بهسازی شده با روش تضعیف نامتقارن تیر 87 100 244684 10.48303/bese.2021.244684 FA محسن گرامی دانشیار گروه مهندسی زلزله، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران وحید بهاری زرگر دانش آموخته کارشناسی ارشد عمران زلزله، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران محمد بحیرایی دانش آموخته دکتری عمران زلزله، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران Journal Article 2019 12 05 After the Northridge earthquake in 1994, numerous reports of failures due to brittle fractures of the weld joint for steel structures were presented in various Codes. One of the ideas to solve this problem was to promote the plastic hinge away from the weld through the intentional weakening of the beam at a certain distance from the column. In this idea, by weakening the top and bottom flanges of the beam at a certain distance from the column, the ductility of the connection is increased and brittle failure in the weld area is prevented. The existing steel frame buildings that are designed according to Pre-Northridge seismic provisions need to be rehabilitated to prevent the connections from experiencing brittle fracture at their welds. The presence of concrete slab in existing steel buildings imposes economic problems in retrofit projects. Asymmetrically weakening the beam is considered as an appropriate method for seismic rehabilitation of steel frame connections in which the rehabilitation action is conducted through intentional weakening the bottom flange of the beam and without the difficulty of removing concrete slab. Two techniques “reduction” and “heat induction” are among suggested methods for asymmetric weakening of the beam. In the “reduction” technique, the weakening action is conducted by cutting some parts of the beam bottom flange at a certain distance from the connection. In the “heat induction” technique, the weakening action is conducted by applying a special process of heating to the bottom flange of the beam at a certain distance from the column. In this heating process, which reduces the yield and ultimate strength by 35% and 25%, respectively, in other words the steel is annealed. This drop in strength in the heated area causes the plastic hinge to move over the beam.<br />The main purpose of this study is to investigate and compare the seismic behavior of low-, medium-, and high-rise 2-D steel frames improved through these two techniques “reduction” and “heat induction” under far-field and near-field earthquakes, numerically.<br />Two types of verification are conducted to ensure the accuracy of numerical modeling. First, 2-D rehabilitated connections through two “reduction” and “heat induction” techniques are verified with experimental results. Then, three 2-D frames are verified with Gupta & Krawinkler results.<br />The results of the frames analysis showed that inter-story drift and total rotation of rehabilitated frames by “reduction” technique were on average 15 percent more than rehabilitated frames by “heat induction” technique. This indicates the defect of the improved connection through the “reduction” technique in low elastic stiffness and torsional-lateral instability compared to the "heat application" technique. In addition, it was determined, as the height of the frame increases, the effectiveness of far-field earthquakes decreases and near field earthquakes show their effects on the structure more. As the ratio of the earthquake pulse period to the main period of the structure increases, the imposed deformation on the frames increase. So that, if this ratio is equal to one, the maximum relative drift for the frames is estimated. تضعیف نامتقارن تیر به‌عنوان یک راهکار مناسب جهت بهسازی اتصالات مطرح است که عمل انتقال مفصل پلاستیک در آن با تضعیف بال تحتانی تیر و بدون نیاز به دشواری­ های برداشتن دال بتنی انجام می­ شود. دو روش «کاهش مقطع» و «اعمال حرارت» از جمله راهکارهای معرفی شده برای تضعیف نامتقارن تیر می باشند. هدف اصلی این مقاله، بررسی و مقایسه رفتار لرزه­ای سه نوع قاب دو بعدی کوتاه، متوسط و بلندمرتبه بهسازی شده با این دو روش تحت زلزله­ های حوزه نزدیک و دور به‌صورت عددی است. بدین‌منظور، جهت اطمینان از دقت مدل‌سازی عددی، نتایج عددی سه نوع قاب و اتصالات دو بعدی بهسازی شده ­ی قاب­ ها با نتایج آزمایشگاهی صحت­ سنجی شد. نتایج تحلیل قاب­ ها نشان می­ دهد، دریفت نسبی و دوران کلی قاب‌های بهسازی شده با روش «کاهش مقطع» به‌طور میانگین 15 درصد بیشتر از قاب‌های بهسازی شده با روش «اعمال حرارت» می ­باشد. قاب‌های بیست طبقه با توجه به کاهش دوران کلی آنها نسبت به قاب‌های سه‌طبقه، با افزایش طول پریود آنها، می­ توانند متحمل خرابی بیشتری ­شوند. با بالا رفتن ارتفاع طبقات قاب­ ها، اثربخشی زلزله­ های حوزه دور کمتر شده و زلزله ­های حوزه نزدیک تأثیرات خود را بر روی سازه بیشتر نشان می­ دهد. https://www.bese.ir/article_244684_82bc0ccf221411fe06c6db933cc1da42.pdf