Evaluation of Spectrum Correction Factor of Iranian Code No.2800 to Determine the Seismic Parameters of RC Moment-Resisting Frames in Near Field Earthquakes

Document Type : Research Article

Authors

1 M.Sc. Student, Department of Civil Engineering, Razi University, Kermanshah, Iran

2 Associate Professor, Department of Civil Engineering, Razi University, Kermanshah, Iran

Abstract

Iran's Standard No. 2800 provides a code for the design of structures against earthquake loads. Due to the fact that mostly, far-field records have been used to prepare the seismic design spectra, in order to consider the destructive effects of near-field earthquakes in the 4th edition of Standard 2800, the incremental spectral correction coefficient (N) was introduced. In this paper, the accuracy and estimation of the value of this coefficient for five structures of special reinforced concrete moment-resisting frame with the number of floors from 3 to 15 are evaluated. Due to the fact that the increase in seismic requirements under the pulses of near-fault earthquakes is not the same for all seismic response parameters, so different correction coefficients can be used to estimate displacement response quantities and force quantities. For this purpose, first, the structures are statically analyzed according to the criteria of Iranian Standard 2800 and are designed according to the criteria of Article 9 of the National Regulations of Iran. Then the dimensions of beams, columns and rebars required by the structures are determined. After that the response spectrum of single-degree of freedom system to a set of records (including seven far-field records, and 22 near-field records) is calculated, and then by using incremental dynamic analysis, the seismic response of structures at different seismic intensities is calculated. By calculating the response ratio of structures under near-field records to far-field records, the value of the N-coefficient is calculated. Based on the results, the value of the N-coefficient of the standard spectrum of Standard 2800 is suitable for estimating the base shear demand of structures, but this coefficient is not accurate enough to estimate the need for lateral drift of structures. In general, the coefficients obtained from elastic and inelastic analyzes for the need for displacement in reinforced concrete flexural frame structures are higher than the values provided by the Standard 2800. This difference has reached 58% in some structures. It was also observed that there is no regular relationship between the 1st period of the structures and the magnitude of the spectral correction coefficient and the magnitude of the spectrum correction decreases with increasing seismic intensity.

Keywords

References

  1. Bolt, B.A. (2004) Seismic input motions for nonlinear structural analysis. ISET Journal of Earthquake Technology, 41(2), 223-232.
  2. Mavroeidis, G., Dong, G., and Papageorgiou, A. (2004) Near‐fault ground motions, and the response of elastic and inelastic single‐degree‐of‐freedom (SDOF) systems. Earthquake Engineering and Structural Dynamics, 33(9), 1023-1049.
  3. Somerville, P.G., et al. (1997) Modification of empirical strong ground motion attenuation relations to include the amplitude and duration effects of rupture directivity. Seismological Research Letters, 68(1), 199-222.
  4. Alavi, B. and Krawinkler, H. (2004) Behavior of moment‐resisting frame structures subjected to near‐fault ground motions. Earthquake Engineering & Structural Dynamics, 33(6), 687-706.
  5. Bray, J.D. and Rodriguez-Marek, A. (2004) Characterization of forward-directivity ground motions in the near-fault region. Soil Dynamics and Earthquake Engineering. 24(11), 815-828.
  6. Yang, D., Pan, J., and Li, G. (2010) Interstory drift ratio of building structures subjected to near-fault ground motions based on generalized drift spectral analysis. Soil Dynamics and Earthquake Engineering. 30(11), 1182-1197.
  7. Lin, K.-C., et al. (2010) Seismic reliability of steel framed buildings. Structural Safety, 32(3), 174-182.
  8. Champion, C. and Liel, A. (2012) The effect of near‐fault directivity on building seismic collapse risk. Earthquake Engineering and Structural Dynamics, 41(10), 1391-1409.
  9. Gerami, M. and Abdollahzadeh, D. (2012) Estimation of forward directivity effect on design spectra in near field of fault. Journal of Basic and Applied Scientific Research, 2(9), 8670-8686.
  10. Vahdani, R., Gerami, M., and Razi, M. (2018) Assessment of spectrum modification factor for design of steel moment frames in near fault regions. Structural Engineering and Construction, 5(1), 71-87 (in Persian).
  11. Gerami, M., Mashayekhi, A., and Siahpolo, N. (2017) Computation of R factor for steel moment frames by using conventional and adaptive pushover methods. Arabian Journal for Science and Engineering, 42, 1025-1037.
  12. Building and Housing Research Center (2015) Iranian Code of Practice for Seismic Resistant Design of Buildings (Standard No. 2800) 4th Edition, Tehran.
  13. Razi, M. (2017) Inelastic Spectral Modification  for Seismic Assessment of Steel Moment Resisting Frames in Near Fault Areas. D. Dissertation, Semnan University (in Persian).
  14. Baker, J.W. (2007) Quantitative classification of near-fault ground motions using wavelet analysis. Bulletin of the Seismological Society of America, 97(5), 1486-1501.
  15. Sehhati, R., et al. (2011) Effects of near-fault ground motions and equivalent pulses on multi-story structures. Engineering Structures, 33(3), 767-779.
  16. Kumar, M., Stafford, P.J., and Elghazouli, A.Y. (2013) Influence of ground motion characteristics on drift demands in steel moment frames designed to Eurocode 8. Engineering Structures, 52, 502-517.
  17. Ashayeri, I., Memari, M.A., and Haghshenas, E. (2021) Seismic microzonation of Sarpol-e-zahab after Mw 7.3 2017 Iran earthquake: 1D-equivalent linear approach. Bulletin of Earthquake Engineer-ing, 19, 605-622.
  18. A Computer Program for Static and Dynamic Analysis for Framed Structures (2021) Available: www.seismosoft.com (online).
  19. Scott, M.H. and Fenves, G.L. (2006) Plastic hinge integration methods for force-based beam-column elements. Journal of Structural Engineering, 132(2), 244-252.
  20. Menegotto, M. (1973) Method of analysis for cyclically loaded RC plane frames including changes in geometry and non-elastic behavior of elements under combined normal force and bending. of IABSE Symposium on Resistance and Ultimate Deformability of Structures Acted on by Well Defined Repeated Loads.
  21. Mander, J.B., Priestley, M.J., and Park, R. (1988) Theoretical stress-strain model for confined concrete. Journal of Structural Engineering. 114(8), 1804-1826.
  22. Pinho, R. and Elnashai, A. (2000) Dynamic collapse testing of a full-scale four storey RC frame. ISET Journal of Earthquake Technology, 37(4), 143-163.
  23. Haselton, C., et al. (2012) Selecting and scaling earthquake ground motions for performing response-history analyses. Proceedings of the 15th World Conference on Earthquake Engineering, Earthquake Engineering Research Institute Oakland, CA, USA.
  24. Vamvatsikos, D. and Cornell, C.A. (2002) Incre-mental dynamic analysis. Earthquake Engineering and Structural Dynamics, 31(3), 491-514.
  25. Leyendecker, E.V., et al. (2000) Development of ma×imum considered earthquake ground motion maps. Earthquake Spectra, 16(1), 21-40.

Files

History

  • Receive Date: 07 April 2022
  • Revise Date: 28 June 2022
  • Accept Date: 17 July 2022

Share

How to cite

Statistics